Dd-technologies TruClose Heavy Duty Round Post Manuel d'utilisateur
Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la maison Dd-technologies TruClose Heavy Duty Round Post. D&D Technologies TruClose Heavy Duty Round Post User Manual Manuel d'utilisatio
- Page / 1
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
INSTALLATION INSTRUCTIONS TCHDRND1
For a downloadable Adobe Acrobat (.PDF) version of our Limited LIFETIME WARRANTY,
go to our website at www.ddtechglobal.com
MAINTENANCE & REQUIREMENTS:
• Always use two ROUND-POST HINGES on any one gate.
• Ensure the gate does not swing beyond 180˚.
• Each hinge must have equal tension at all times.
• Remove all other types of hinges and self-closing devices.
• Do not lubricate these hinges with petroleum-based lubricants. Use only
powdered graphite.
• Never remove ROUND-POST HINGES from gate until spring tension is released.
• Do not physically alter hinge bodies by cutting, milling, machining or grinding any part.
• For safety, remove protruding bolts/screws after installation by cutting, grinding and/or ling.
fits both left-hand or
right-hand hinged gates
•INSTR-TCHDRND1_1 11 11
TCHDRND1000PA
Procedure
In preparation for installation of the hinges, choose the appropriate round-post adaptors by
placing them onto the post to determine the correct t. Each adaptor should t neatly around
the diameter of the gate and the post. Discard unwanted adaptors.
1. Insert the adaptors for the gate frame into the rear of the hinges, ensuring the location
‘lugs’ at the rear of the adaptors t snugly into the hinges.
2. Take the hinges and align/position them onto the gate to suit the style of latch used
(see Diagrams A & B).
3. Take the hex-shaped screws (12g–24x25mm ) and secure the hinges to the gate. A pilot
hole of
3
/16" (4.8mm) will be required. Note the need for hinge vertical alignment (level), as
shown in Diagram C. The wafer-head screws (10g–24x22mm) for the side-fixing legs are to be
installed once the gate is hung.
4. Insert the post adaptors into the rear of the hinges.
5. Take the gate and locate it into the desired position/height. You may need to prop up
and support the gate temporarily during installation.
6. Ensuring the gate is correctly aligned with the fence (see Diagrams A & B), take the
remaining hex-head screws and secure the hinges (the gate) to the post. Again, pilot hole of
3
/16" (4.8mm) will be required.
7. Open the gate sufciently to allow installation of the screws for
the side-xing legs. Note there are four screws remaining for each
hinge. A pilot hole of
5
/32" (4mm) will be required.
8. Adjust tension: Remove the endcap at the “adjustable” end
of the hinge. Use the large slot-head screwdriver to depress and
turn the internal spring-loaded adjustor counter-clockwise. Hold the
desired tension and allow to rise back into retention sleeve. Replace
endcap.
The gate is now ready for use. Ensure the gate cannot swing beyond
180˚ through the line of the fence by installing a latch or ‘gate stop’.
Some important points concerning the installation of ‘ROUND-POST HINGES’:
• Note that each hinge has five different-sized adaptors to t various diameters
of posts or gate frames.
• The adaptors in this pack t the following diameters:
GATES (to t the small side of the hinge): 1
3
/8“, 1
5
/8“ (35 & 41mm)
POSTS (to t the large side of the hinge): 1
7
/8“ and 2“, 2
3
/8“, 2
7
/8“ (48-51, 60 & 73mm)
• Wherever possible, keep the “adjustable end” of the hinge (indicated by screw in
endcap) facing up for ease of tension adjustment.
• The hinges should be installed as far apart vertically as is practical.
Tools required: Electric drill/cordless drill,
3
/16" (4.8mm) &
5
/32" (4mm) drill
bits, Phillips No. 2 screwdriver (hand & power),
5
/16" hex-head driver and
large slot-head screwdriver.
STRAIGHT
OFFSET
FLUSH-MOUNTED LATCHES
Maintain 180˚ alignment during installation
to ensure accurate, reliable closure.
CENTER-MOUNTED LATCHES
The hinge can be offset slightly to help align
the latch in the middle of the latch post.
Diagram a
Diagram B
Post
Gate
Post
Gate
LINE OF
FENCE
LEVEL
IMPORTANT
Keep top and bottom hinges
vertically aligned (level)
Diagram C
LINE OF
FENCE
Minimum gap between hinge post and gate:
3/4" (19mm).
Maximum gap: 1-3/8" (35mm).
m
www.ddtechglobal.com
AUSTRALIA: Unit 6, 4-6 Aquatic Dr, Frenchs Forest NSW 2086
USA: 7731 Woodwind Drive, Huntington Beach, CA 92647
1
Résumé du contenu
Page 1 - •INSTR-TCHDRND1_1 11 11
INSTALLATION INSTRUCTIONS TCHDRND1For a downloadable Adobe Acrobat (.PDF) version of our Limited LIFETIME WARRANTY, go to our website at www.ddt
Produits connexes et manuels pour Pour la maison Dd-technologies TruClose Heavy Duty Round Post
(2 pages)
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.735 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels