Dd-technologies MagnaLatch Top Pull Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la maison Dd-technologies MagnaLatch Top Pull. D&D Technologies MagnaLatch Top Pull User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 2
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
For swimming and other child safety gates, most safety standards specify the
following minimum height requirements as being from the bottom of the gate:
1) latch release knob ‘F’ at minimum 54” (1370mm); 2) fence height of between 48” & 72” (1220 &
1830mm). Always confirm these and other requirements with the appropriate pool or safety authorities in your area and install
this latch in accordance with the local fence/barrier codes and regulations. Also, pool gate must open outward, away from the
pool, so this latch must be fitted to the outside of a pool gate. Tools: Electric and cordless drills, drill bits, Phillips No. 2 screwdriver
(hand & powered types). Note: If mounting to steel or vinyl with metal inserts, it is advisable to pre-drill the holes to prevent
screw breakage.
Swimming pool fences, gates and latches cannot substitute for adult supervision. If using this latch on a swimming pool gate, consult all appropriate local
authorities for safety requirements.
The latch will operate properly only if installed and maintained in accordance with these instructions.
MAINTENANCE: REMOVE KEY FROM LOCK AFTER USE. Do not lubricate the latch with petroleum-based lubricants at any time; use only powdered graphite.
Ensure all screws or bolts are tightened firmly and that the release knob [F] and latching bolt are kept free of sand, ice and other debris which could impair latch
performance. Grind or remove any protruding fasteners after installation.
For a downloadable Adobe Acrobat (.PDF) version of our Limited LIFETIME WARRANTY,
go to our website at www.ddtechglobal.com
INSTALLATION INSTRUCTIONS
For swimming and other child safety gates, most safety standards specify the
following minimum height requirements above the finished ground/fixing surface:
1) latch release knob ‘F’ at minimum 1500mm (59”); 2) fence height of between 1220mm & 1520mm (48” & 60”)
Always confirm these and other requirements with the appropriate pool or safety authorities in your area and install this latch
in accordance with the local fence/barrier codes and regulations. Also, pool gate must open outward, away from the pool, so
this latch must be fitted to the outside of a pool gate. Tools: Electric or cordless drill, drill bits, Phillips No. 2 screwdriver (hand &
powered types). Note: For heavy gauge steel sections it is advisable to pre-drill the holes to prevent screw breakage.
Swimming pool fences, gates and latches cannot substitute for adult supervision. If using this latch on a swimming pool gate, consult all appropriate local authorities
for safety requirements.
The latch will operate properly only if installed and maintained in accordance with these instructions.
MAINTENANCE: REMOVE KEY FROM LOCK AFTER USE. Do not lubricate the latch with petroleum-based lubricants at any time; use only powdered graphite.
Ensure all screws or bolts are tightened firmly and that the release knob [F] and latching bolt are kept free of sand, ice and other debris which could impair latch
performance. Grind or remove any protruding fasteners after installation.
For a downloadable Adobe Acrobat (.PDF) version of our Limited LIFETIME WARRANTY,
go to our website at www.ddtechglobal.com
INSTALLATION INSTRUCTIONS
Installation Procedure
1. The gap between gate frame and latch post must be between
3
/8” (10mm) and 1
7
/16” (37mm);
3
/4” (19mm) is ideal.
2. Determine the location of the hole for Mounting Bracket ‘A’ by measuring up from the bottom of the gate,
for 54” knob height measure up 36
3
/8” (925mm).
Place Mounting Bracket ‘A’ on the post as shown, and, using one of the 1” (25mm) wafer-head,
self-drilling screws, fix the bracket to the post – through the side fixing hole. Now install two
more of these screws through the front of the bracket.
3. To install Mounting Bracket ‘B’ measure up from Bracket ‘A’ 13
3
/8” (340mm). Mark this point
and fix as ‘2’ above.
NOTE: For 48” (1220mm) fences without an extra-high post, this measurement should be
5” (125mm) for 54” (1370mm) knob height from bottom of gate.
Place the Bracket ‘B’ so that the holes are centered on the marked line. Fix bracket
using the same screws as per Bracket ‘A’. (NOTE: In some applications it may be
necessary to add a spacer to clear a post cap. Spacers S1, S2 & S3 are for this
purpose and should be inserted behind the mounting brackets during
installation.)
4. Take the main LATCH BODY ‘C’
and slide it down onto the Mounting
Bracket ‘B’, ensuring the rear track of
the latch slides over brackets ‘B’, then ‘A’.
5. Slide the Latch Body until the bottom
of the latch aligns neatly with the lower
end of Bracket ‘A’ (see dashed line ‘L’).
Take the single
3
/8” (10mm) counter-
sunk screw ‘H’ and secure the Latch
Body – DO NOT use a power or cordless
drill – to Bracket ‘A’.
6. The final part to be installed is the
STRIKER BODY ‘D’. Note that the Striker
Body slides on a dovetail track within
the Mounting Plate (P1, P2). NEVER use
a powered drill to adjust this screw.
See Diagram ‘E’. Locate the Striker
Body assembly onto the post as shown.
Position the Striker Body to obtain a
1
/8” (3mm) gap between the lower part
of the latch and the top of the Striker
Body, as shown. Maintain this gap and
fix two 1” (25mm) screws through the
two main holes of the Striker Body.
The two, small (cylindrical) dress plugs
supplied should now be pressed into the
screw holes.
7. a) Open the gate and secure two more screws through the side leg of the Mounting Plate. Note: If the width of the gate
frame is 1
1
/2” (38mm) or greater, follow step b)…
b) With the gate open, adjust the Striker Body using the screwdriver in the adjustment screw. Turn counter-clockwise until
the two holes are exposed, as in Diagram (P2). Fix the two remaining screws to secure the Mounting Plate.
8. Use the screwdriver to adjust the Striker Body to align with the Latch Body, as shown in Diagram ‘E’. Open and close the
gate to check the latch operates correctly. Adjust as necessary at any time after installation to ensure safe operation of the
latch. NOTE: Future vertical adjustment of the latch can be achieved by removing the screw ‘H’, sliding the Latch Body up or
down the post to obtain correct operational alignment, then inserting the screw into the appropriate hole.
Installation Procedure
1. The gap between gate frame and latch post must be between 10mm (
3
/8”) and 37mm (1
7
/16”); 19mm (
3
/4”) is ideal.
2. Determine the location of the hole for Mounting Bracket ‘A’ by measuring up 1050mm (41
3
/8”) from
the finished ground/fixing surface.
Place Mounting Bracket ‘A’ on the post as shown, and, using one of the 25mm (1”) wafer-head,
self-drilling screws, fix the bracket to the post – through the side fixing hole. Now install two
more of these screws through the front of the bracket.
3. To install Mounting Bracket ‘B’ measure up from Bracket ‘A’ 340mm (13
3
/8”).
Mark this point.
NOTE: For 1220mm (48”) fences without an extra-high post, this measurement should be
125mm (5”).
Place the Bracket ‘B’ so that the holes are centered on the marked line. Fix bracket
using the same screws as per Bracket ‘A’. (NOTE: In some applications it may be
necessary to add a spacer to clear a post cap. Spacers S1, S2 & S3 are for this
purpose and should be inserted behind the mounting brackets during
installation.)
4. Take the main LATCH BODY ‘C’ and slide it down onto the
Mounting Bracket ‘B’, ensuring the rear track of the latch
slides over brackets ‘B’, then ‘A’.
5. Slide the Latch Body until the bottom of the
latch aligns neatly with the lower end of
Bracket ‘A’ (see dashed line ‘L’). Take
the single 10mm (
3
/8”) countersunk
screw ‘H’ and secure the Latch Body –
DO NOT use a power or cordless drill
– to Bracket ‘A’.
6. The final part to be installed is
the STRIKER BODY ‘D’. Note that the
Striker Body slides on a dovetail track
within the Mounting Plate (P1, P2) and
is operated by an internal adjustment
screw; NEVER use a powered drill to
adjust this screw.
See Diagram ‘E’. Locate the Striker Body
assembly onto the post as shown. Posi-
tion the Striker Body to obtain a 3mm
(
1
/8”) gap between the lower part of
the latch and the top of the Striker Body,
as shown. Maintain this gap and fix two
25mm (1”) screws through the two main
holes of the Striker Body. The two, small
(cylindrical) dress plugs supplied should
now be pressed into the screw holes.
7. a) Open the gate and secure two
more screws through the side leg of the Mounting Plate. Note: If the width of the gate frame is 38mm (1
1
/2”) or greater, follow
step b)…
b) With the gate open, adjust the Striker Body using the screwdriver in the adjustment screw. Turn counter-clockwise until the
two holes are exposed, as in Diagram (P2). Fix the two remaining screws to secure the Mounting Plate.
8. Use the screwdriver to adjust the Striker Body to align with the Latch Body, as shown in Diagram ‘E’. Open and close the gate
to check the latch operates correctly. Adjust as necessary at any time after installation to ensure safe operation of the latch.
NOTE: Future vertical adjustment of the latch can be achieved by removing the screw ‘H’, sliding the Latch Body up or down the
post to obtain correct operational alignment, then inserting the screw into the appropriate hole.
• Le système Magna Latch peut être utilisé sur les portillons des barrières de protection
de piscines privatives destinées à un usage familial ou collectif.
• Les barrières de protection de piscine sont destinées à limiter lʼaccès de la piscine à des enfants de moins de cinq ans.
• Il est recommandé dʼinstaller la barrière de protection à un mètre minimum du plan dʼeau. Pour les piscines privatives
à usage individuel, il est recommandé de ne pas installer la barrière trop loin du bassin an de ne pas perdre lʼefcacité
de la barrière.
En matière de barrières de piscine et autres barrières de protection pour les enfants de moins de 5 ans, les normes
de sécurité spécifient entre autres :
1) une barrière d’une hauteur d’au moins 1100 mm (la hauteur minimale entre deux points d’appui doit
toujours être supérieure ou égale à 1100 mm)
2) un système de déverrouillage, en l’occurrence le bouton de déverrouillage, placé à
une hauteur supérieure à 1500 mm à partir du sol à l’extérieur de la zone
protégée.
Par ailleurs, lorsque le moyen d’accès choisi est
pivotant , l’ouverture doit se faire vers
l’extérieur de la piscine. De fait, la
serrure Magna-Latch doit être fixée sur
le côté extérieur de la barrière.
Il est impératif de demander confirma-
tion de ces exigences et d’autres normes
éventuelles auprès des professionnels de
la piscine et des autorités en charge de
l’équipement ou de la sécurité de votre
région et d’installer cette serrure en
parfaite conformité avec les normes et
les réglementations len vigueur.
Outils : perceuse électrique ou sans fil,
mèches, tournevis Phillips No. 2 (manuel
& électrique). Note : pour les mont-
ants en acier de forte épaisseur, il est
conseillé d’effectuer un pré-perçage des
trous, afin d’éviter de briser les vis.
Procédure
d’installation
1. L’écart entre le cadre du portil-
lon et le montant sur lequel sera
placée la serrure doit être compris
entre 10 mm et 37 mm, la distance
idéale étant de 19 mm.
2. Marquer lʼemplacement du trou
nécessaire au montage de la patte
de xation A à 1100 mm du sol ni
ou de la surface de xation.
Visser la patte de fixation A sur
le côté du montant de la barrière
comme indiqué sur le schéma, à l’aide de l’une des vis autoperforantes à tête wafer 25 mm. Finir de fixer
la patte de fixation à l’aide de deux autres vis semblables sur la face avant du montant.
3. Pour installer la patte de fixation B, tracer une ligne à 125 mm au-dessus de la patte de fixation A
(prendre pour repère la vis centrale de la patte de fixation A).
Positionner la patte de fixation B de manière à ce que les
trous soient centrés sur la ligne tracée, puis la fixer à l’aide du même type de vis que pour la patte de
HIGH POST
used in some
markets
MLINSTR0029PA
AUSTRALIA: Unit 6, 4-6 Aquatic Dr, Frenchs Forest NSW 2086
USA: 7731 Woodwind Drive, Huntington Beach, CA 92647
EUROPE: Niasstraat 1, 3531 WR Utrecht, The Netherlands.
www.ddtechglobal.com
ENGLISH – International
ENGLISH – North America
•INSTR MLTP North America 29/11/12
F R A N ÇAIS – Canada
NOTICE DE MONTAGE
Vue de la page 0
1 2

Résumé du contenu

Page 1 - Procédure

For swimming and other child safety gates, most safety standards specify thefollowing minimum height requirements as being from the bottom of the gate

Page 2 - Procedimiento de

ImportantePara puertas para piscinas y otras puertas de seguridad para niños la mayoría de los estándares de seguridad especifican los siguientes requi

Commentaires sur ces manuels

Pas de commentaire